Posted on: November 22, 2020 Posted by: admin Comments: 0

KEB F5 INVERTER MANUAL PDF

INSTRUCTION MANUAL. -K COMBIVERT F5. R. ELEVATOR DRIVE. Page 2. Page 3. Table of Contents. 1. General . KEB F5-B AC-Drive Manual. Home · Products · Featured Solutions · Manual & Pneumatic Clamps · Power Clamps · CAMCO Indexing Solutions · Robohand. Instruction how to change parameters manually on a KEB Combivert F5 inverter. This example shows how you change password for to be able.

Author: Jutilar Kaziran
Country: Comoros
Language: English (Spanish)
Genre: Medical
Published (Last): 11 March 2014
Pages: 221
PDF File Size: 18.46 Mb
ePub File Size: 10.47 Mb
ISBN: 702-7-96318-229-5
Downloads: 44884
Price: Free* [*Free Regsitration Required]
Uploader: Fenribar

Via the keypad, provide the direction and then the speed.

This way you will be sure to operate the system within the design specifications of the machine. It is only valid together with the instruction manuals part 1 and part 3. Examples for the arrangement and programming of kb temperature mnual with KTY84 evaluation can be taken from the appilcation manual. The desired function is adjusted with Pn. Comments to this Manuals Your Name.

Connection Terminals Motor terminal strip X1B Name Function U, U 3-phase motor connection V, V W, W Connection for protective earth conductor The motor lines must be parallel passed and con- nected with the respective cross section see tech- nical data.

The connection to a closed cooling circuit is manuao, because the danger of contamination of coolant is very small. Connection Terminals Picture 2.

KEB Combivert F5 (TTL Feedback) Frequency Inverters

Page 21 Connection Terminals Terminal invrter for motor temperature detection and braking transistor monitoring X1D Name Function K1, K2 Braking transistor monitoring optional Connection for temperature detec- tion T1, T2 see chapter ” Temperature detec- tion T1, T2″ Permissible cable cross-sections and tightening torques of the terminals permissible cross-section flexible with wire-end Max.

Read Instruction Manual Part 1 first! HybC means that the feedback card on the inverter has been changed.

Temperature Detection T1, T2 2. Answer questions, earn points and help others Answer questions.

  EON RISE OF THE DRAGONEYE PDF

By pressing ‘print’ button you will print only current page. Page 39 Notes GB – The inverter tells the motor what to do and the encoder send information back to the inverter to verify the operations. Also insure that the inverter is not enabled or in nOP status.

What is the part of the unit in question? If the inverter tells the motor to run at rpm and the feedback tells the inverter it is only running at 5rpm, the inverter will send out more current to get the motor up to speed.

KEB COMBIVERT F5 Instruction Manual

Got it, continue to print. With out knowing part and serial number of the unit in question, I do not know exactly which inverter you are having problems with. If the applied voltage is good then there is a problem with the input stage or the DC bus and the unit will need to be repaired or replaced. Requirements On The Coolant Pay attention to flux direction and check tightness! This causes heat and gas and leads to the destruction of the capacitor. Too much current is being required with the motor shaft not rotating.

Argospete Level 3 Expert Answers. If the capacitor starts running with rated voltage, it is tried to build the oxide film abrupt again. At that point unit should be replaced or repaired.

The inverter is recognizing that terminal 16 is going active but still waiting for another command to enable the inverter. Divq If the capacitor starts running with rated voltage, it is tried to build the oxide film abrupt again. EF is a programmable error triggered by user programmed conditions.

This could also be caused by the encoder feedback loop being defective. If the fan was not functioning the inverter would trip into E. The connection to the cooling system can occur as closed or open cooling circuit. Try to home the system.

  DOMOTICA E INMOTICA VIVIENDAS Y EDIFICIOS INTELIGENTES PDF

Inverter Siemens Micromaster 35 Questions. Don’t show me this message again. To print the manual completely, please, download it. If a decimal shows up after the value is changed, enter must be pressed to save the value.

The following instructions must be observed absolutely when this units are used. PU is a general power stage failure.

Top 20 Inverter KEB COMBIVERT F5 Questions & Answers – Fixya

During assembly pay attention to appropriate protection against contact and fire. Connection Terminals Terminal strip for motor temperature detection and braking transistor monitoring X1D Name Function K1, K2 Braking transistor monitoring optional Connection for temperature detec- tion T1, T2 see chapter ” Temperature detec- tion T1, T2″ Permissible cable cross-sections and tightening torques of the terminals permissible cross-section flexible with wire-end Max.

Recent Popular Answered Unanswered. Enter text from picture: Without knowing the part number of the actual inverter with the problem it is difficult to speculate what the actual problem is. You must confirm the change kwb parameter ec. Inverter Yaskawa F7 Drive Questions. Some of the older F5 inverters utilized a feedback loop so that the inverter could tell if the fan was functioning properly. To ensure a safe operation the coolant output tempe- rature must be 10 K below this temperature.

Error Diagnosis 4. Error diagnosis KEB COMBIVERT Error messages are represented with an

Table of Contents Add to my manuals Add. Also the temperature dependent switching losses are positively effected. If it is present but the invegter does not power up, there is most likely an internal problem. Technical Data – Dimensions and Weights 2. Contact KEB for special or medium frequency motors.

Categories:

Leave a Comment